MX25L1606EM1I-12G您现在的位置:首 页 > MX25L1606EM1I-12G
MX25L1606EM1I-12G The device has a serial peripheral interface and software protocol that allows operation on a simple 3-wire bus. These three bus signals are clock input (SCLK), serial data input (SI), and serial data output (SO). Enable serial access to the device through CS input. When it is in dual output read mode, SI and SO pins change to SIO0 and SIO1 pins for data output. The device provides sequential read operations for the entire chip. After issuing the program/erase command, the program/erase is executed and the automatic program/erase algorithm for the specified page or sector/block location is validated. Program commands are executed as bytes, pages, or words. Erase commands are executed on a sector, block, or entire chip basis. In order to provide users with a convenient interface, a status register is included to indicate the status of the chip. The status read command can be issued to detect the completion status or erase operation of the program by WIP bit. Advanced Security features enhance protection and security features, see the Security Features section for more information. When the device is not running and CS# is high, put it in standby mode. The device uses Macronix's dedicated storage unit, which reliably stores memory contents even after a typical 100,000 program and erase cycles.
MX25L1606EM1I-12G该设备具有串行外围接口和软件协议,允许在简单的3线总线上操作。这三个总线信号是时钟输入(SCLK)、串行数据输入(SI)和串行数据输出(SO)。通过CS输入启用对设备的串行访问。当它处于双输出读取模式时,SI和SO管脚变为用于数据输出的SIO0和SIO1管脚。该设备提供对整个芯片的顺序读取操作。发出程序/擦除命令后,将执行程序/擦除并验证指定页面或扇区/块位置的自动程序/擦除算法。程序命令按字节、页或字执行。擦除命令以扇区、块或整个芯片为基础执行。为了给用户提供方便的接口,包括一个状态寄存器来指示芯片的状态。可发出状态读取命令,通过WIP位检测程序的完成状态或擦除操作。高级安全功能增强了保护和安全功能,有关详细信息,请参阅安全功能部分。当设备未运行且CS#高时,将其置于待机模式。该设备使用Macronix的专用存储单元,即使在典型的100000个程序和擦除周期之后,该单元也能可靠地存储内存内容。
MX25L1606EM1I-12GG基本参数
•单电源操作
-2.7至3.6伏,用于读取、擦除和编程操作
•支持串行外围接口——模式0和模式3
•16777216 x 1位结构或8388608 x 2位(双输出模式)结构
•512个相等扇区,每个扇区4K字节
-任何扇区都可以单独擦除
•32个相同的块,每个块64K字节
-任何块都可以单独擦除
•程序能力
-字节基
-页基(256字节)
•从-1V到Vcc+1V,保护闩锁至100mA
性能
•高性能
-快速存取时间:86MHz串行时钟
-双输出模式串行时钟:80MHz
-快速编程时间:0.6ms(典型值)和3ms(最大值)/页
-字节程序时间:9us(典型值)
-快速擦除时间:40毫秒(典型值)/扇区;0.4秒(典型值)/块
•低功耗
-低有效读取电流:在86MHz时为25mA(最大值)
-低激活编程电流:15毫安(典型值)
-低激活扇区擦除电流:9毫安(典型值)
-低待机电流:15uA(典型值)
-深功率下降模式2uA(典型)
•典型的100000次擦除/程序周期
•20年的数据保留
软件功能
•输入数据格式
-1字节指令码
•高级安全功能
-闭锁保护
BP3-BP0状态位定义区域的大小
对程序和
删除指令
-用于唯一标识符的附加512位安全OTP
•自动擦除和自动编程算法
-自动清除和验证选定位置的数据部门
-通过内部算法自动编程和验证选定页上的数据
乘以程序脉冲宽度(要编程的任何页面都应首先使页面处于擦除状态)
•状态寄存器功能
•电子识别
-JEDEC 1字节制造商ID和2字节设备
身份证件(ID)
-用于1字节设备ID的RES命令
-用于1字节制造商ID和1字节设备ID
•支持串行闪存可发现参数(SFDP)
模式
硬件特性
•包装PACKAGE
- 16-pin SOP (300mil)
- 8-pin SOP (150mil)
- 8-pin SOP (200mil)
- 8-pin PDIP (300mil)
- 8-land WSON (6x5mm)
- 8-land USON (4x4mm)
- 24-Ball BGA
-所有产品均符合RoHS标准