USB-IF Hi-Speed certified to the Universal Serial Bus Specification Rev 2.0

Interface compliant with the ULPI Specification revision 1.1 in 8-bit mode

Industry standard UTMI+ Low Pin Interface (ULPI) Converts 54 UTMI+ signals into a standard 12 pin Link controller interface

54.7mA Unconfigured Current (typical) - ideal for bus powered applications

83uA suspend current (typical) - ideal for battery powered applications

Latch-Up performance exceeds 150 mA per EIA/JESD 78, Class II

ESD protection levels of ±8kV HBM without external protection devices

Integrated protection to withstand IEC61000-4-2 ESD tests (±8kV contact and ±15kV air) per 3rd party test facility

Supports FS pre-amble for FS hubs with a LS device attached (UTMI+ Level 3)

Supports HS SOF and LS keep-alive pulse

Includes full support for the optional On-The-Go (OTG) protocol detailed in the On-The-Go Supplement Revision 1.0a specification

Supports the OTG Host Negotiation Protocol (HNP) and Session Request Protocol (SRP)

Allows host to turn VBUS off to conserve battery power in OTG applications

Supports OTG monitoring of VBUS levels with internal comparators. Includes support for an external VBUS or fault monitor.

Low Latency Hi-Speed Receiver (43 Hi-Speed clocks Max) allows use of legacy UTMI Links with a ULPI wrapper

Integrated Pull-up resistor on STP for interface protection allows a reliable Link/PHY start-up with slow Links (software configured for low power)

Internal 1.8 volt regulators allow operation from a single 3.3 volt supply

Internal short circuit protection of ID, DP and DM lines to VBUS or ground

Integrated 24MHz Crystal Oscillator supports either crystal operation or 24MHz external clock input

Internal PLL for 480MHz Hi-Speed USB operation

Industrial Operating Temperature -40°C to +85°C

32 pin, QFN RoHS Compliant package (5 x 5 x 0.90 mm height)

Cell Phones

PDAs

MP3 Players

Scanners

External Hard Drives

Digital Still and Video Cameras

Portable Media Players

Printers

USB-IF Hi-Speed certified to the Universal Serial Bus Specification Rev 2.0

Interface compliant with the ULPI Specification revision 1.1 in 8-bit mode

Industry standard UTMI+ Low Pin Interface (ULPI) Converts 54 UTMI+ signals into a standard 12 pin Link controller interface

54.7mA Unconfigured Current (typical) - ideal for bus powered applications

83uA suspend current (typical) - ideal for battery powered applications

Latch-Up performance exceeds 150 mA per EIA/JESD 78, Class II

ESD protection levels of ±8kV HBM without external protection devices

Integrated protection to withstand IEC61000-4-2 ESD tests (±8kV contact and ±15kV air) per 3rd party test facility

Supports FS pre-amble for FS hubs with a LS device attached (UTMI+ Level 3)

Supports HS SOF and LS keep-alive pulse

Includes full support for the optional On-The-Go (OTG) protocol detailed in the On-The-Go Supplement Revision 1.0a specification

Supports the OTG Host Negotiation Protocol (HNP) and Session Request Protocol (SRP)

Allows host to turn VBUS off to conserve battery power in OTG applications

Supports OTG monitoring of VBUS levels with internal comparators. Includes support for an external VBUS or fault monitor.

Low Latency Hi-Speed Receiver (43 Hi-Speed clocks Max) allows use of legacy UTMI Links with a ULPI wrapper

Integrated Pull-up resistor on STP for interface protection allows a reliable Link/PHY start-up with slow Links (software configured for low power)

Internal 1.8 volt regulators allow operation from a single 3.3 volt supply

Internal short circuit protection of ID, DP and DM lines to VBUS or ground

Integrated 24MHz Crystal Oscillator supports either crystal operation or 24MHz external clock input

Internal PLL for 480MHz Hi-Speed USB operation

Industrial Operating Temperature -40°C to +85°C

32 pin, QFN RoHS Compliant package (5 x 5 x 0.90 mm height)

Cell Phones

PDAs

MP3 Players

Scanners

External Hard Drives

Digital Still and Video Cameras

Portable Media Players

Printers