2020年MICROCHIP KSZ9031MNXIC现货供应，厂商MICROCHIP_封装QFN64_批号 22+-深圳市宝星微科技有限公司

库存搜索

技术资料

KSZ9031MNXIC您现在的位置：首页 > KSZ9031MNXIC

查看大图

KSZ9031MNXIC
宝星微库存：650 PCS
厂商： MICROCHIP
封装： QFN64
年份： 22+
备注：只供应进口原装正品深圳现货华强广场A座20F-G
PDF：

KSZ9031MNXIC

The KSZ9031 is a completely integrated triple-speed (10Base-T/100Base-TX/1000Base-T) Ethernet physical-layer transceiver for transmission and reception of data on standard CAT-5 unshielded twisted pair (UTP) cable.

The KSZ9031MNX offers the industry-standard GMII/MII (Gigabit Media Independent Interface/Media Independent Interface) for connection to GMII/MII MACs in Gigabit Ethernet processors and switches for data transfer at 1000Mbps or 10/100Mbps. The KSZ9031RNX provides the reduced gigabit media independent interface (RGMII).

The KSZ9031 reduces board cost and simplifies board layout by using on-chip termination resistors for the four differential pairs and by integrating an LDO controller to drive a low-cost MOSFET to supply the 1.2V core. The KSZ9031 offers diagnostic features to facilitate system bring-up and debugging in production testing and in product deployment. Parametric NAND tree support enables fault detection between KSZ9031 I/Os and the board. The LinkMD® TDR-based cable diagnostic identifies faulty copper cabling. Remote and local loopback functions verify analog and digital data paths.

The standard KSZ9031RNX is available in the 48-pin, lead-free QFN package, and the AEC-Q100 automotive qualified parts, KSZ9031RNXUB-VAO and KSZ9031RNXVB-VAO, are available in the 48-pin lead-free WQFN package. The KSZ9031MNX is available in a 64-pin, lead-free QFN package.

KSZ9031是一款完全集成的三速(10Base-T/100Base-TX/1000Base-T)以太网物理层收发器，用于在标准CAT-5非屏蔽双绞线(UTP)电缆上发送和接收数据。

KSZ9031MNX提供行业标准的GMII/MII(千兆位媒体独立接口/媒体独立接口)，用于连接到千兆位以太网处理器和交换机中的GMII/MII MAC，以1000Mbps或10/100Mbps的速度传输数据。KSZ9031RNX提供精简的千兆位媒体独立接口(RGMII)。

KSZ9031对四个差分对使用片内端接电阻，并集成一个LDO控制器来驱动低成本MOSFET为1.2V内核供电，从而降低电路板成本并简化电路板布局。KSZ9031提供诊断功能，有助于生产测试和产品部署中的系统启动和调试。参数NAND树支持实现ksz 9031 I/o和电路板之间的故障检测。基于LinkMD TDR的电缆诊断可识别有故障的铜缆。远程和本地回送功能验证模拟和数字数据路径。

标准KSZ9031RNX采用48引脚无铅QFN封装，AEC-Q100汽车认证器件KSZ9031RNXUB-VAO和KSZ9031RNXVB-VAO采用48引脚无铅WQFN封装。KSZ9031MNX采用64引脚无铅QFN封装。

Product Features 产品特性

Single-chip 10/100/1000Mbps IEEE 802.3 compliant Ethernet transceiver
KSZ9031Mxx feature GMII/MII standard interface with 3.3V/2.5V/1.8V tolerant I/Os
KSZ9031Rxx feature RGMII timing supports on-chip delay according to RGMII Version 2.0, with programming options for external delay and making adjustments and corrections to TX and RX timing paths
GMII/MII/RGMII with 3.3V/2.5V/1.8V tolerant I/Os
Auto-negotiation to automatically select the highest linkup speed (10/100/1000Mbps) and duplex (half/full)
On-chip termination resistors for the differential pairs
On-chip LDO controller to support single 3.3V supply operation – requires only one external FET to generate 1.2V for the core
Jumbo frame support up to 16KB
125MHz Reference Clock Output
Energy-detect power-down mode for reduced power consumption when the cable is not attached
Wake-on-LAN (WOL) support with robust custom-packet detection
AEC-Q100 qualified for automotive applications (KSZ9031RNXUB-VAO, KSZ9031RNXVB-VAO)
Programmable LED outputs for link, activity, and speed
Baseline wander correction
LinkMD® TDR-based cable diagnostic to identify faulty copper cabling
Parametric NAND tree support to detect faults between chip I/Os and board
Loopback modes for diagnostics
Automatic MDI/MDI-X crossover to detect and correct pair swap at all speeds of operation
Automatic detection and correction of pair swaps, pair skew, and pair polarity
MDC/MDIO management interface for PHY register configuration
Interrupt pin option
Power-down and power-saving modes
Core (DVDDL, AVDDL, AVDDL_PLL): 1.2V (external FET or regulator)
VDD I/O (DVDDH): 3.3V, 2.5V, or 1.8V
Transceiver (AVDDH): 3.3V or 2.5V (commercial temp)
Available in 48-pin QFN (7mm x 7mm) and 64-pin QFN (8mm x 8mm) packages
符合IEEE 802.3标准的单芯片10/100/1000Mbps以太网收发器
KSZ9031Mxx具有GMII/MII标准接口，支持3.3V/2.5V/1.8V输入/输出
KSZ9031Rxx特性RGMII时序支持符合RGM ii 2.0版的片内延迟，具有外部延迟编程选项，并可对TX和RX时序路径进行调整和校正
GMII/MII/RGMII，支持3.3V/2.5V/1.8V输入/输出
自动协商，自动选择最高连接速度(10/100/1000Mbps)和双工(半双工/全双工)
差分对的片内端接电阻
片内LDO控制器支持3.3V单电源供电，只需一个外部FET为内核产生1.2V电压
支持高达16KB的巨型帧
125MHz参考时钟输出
未连接电缆时，节能检测省电模式可降低功耗
支持局域网唤醒(WOL ),具有强大的自定义数据包检测功能
AEC-Q100符合汽车应用要求(KSZ9031RNXUB-VAO，KSZ9031RNXVB-VAO)
链接、活动和速度的可编程LED输出
基线漂移校正
基于LinkMD TDR的电缆诊断，用于识别故障铜缆
参数NAND树支持检测芯片I/o和电路板之间的故障
诊断的回送模式
自动MDI/MDI-X交叉，可在所有运行速度下检测和纠正线对交换
自动检测和纠正线对交换、线对偏斜和线对极性
PHY寄存器配置的MDC/MDIO管理接口
中断引脚选项
掉电和省电模式
内核(DVDDL、AVDDL、AVDDL_PLL): 1.2V(外部FET或调节器)
VDD输入/输出(DVDDH): 3.3V、2.5V或1.8V
收发器(AVDDH): 3.3V或2.5V(商用温度)
提供48针QFN(7毫米x 7毫米)和64针QFN(8毫米x 8毫米)封装

首页

产品中心

现货库存

服务中心

关于我们

联系我们

查看大图

Product Features 产品特性

Product Features 产品特性

Skype

whatapp

Hotline

E-mail

首 页

产品中心

现货库存

服务中心

关于我们

联系我们

查看大图

Product Features 产品特性

Product Features 产品特性

Skype

whatapp

Hotline

E-mail

首页